时间:2024-04-10人气:作者:未知
1.在基于IOS的交换机上设置主机名/系统名:
switch(config)# hostname hostname
在基于CLI的交换机上设置主机名/系统名:
switch(enable) set system name name-string
2.在基于IOS的交换机上设置登录口令:
switch(config)# enable password level 1 password
在基于CLI的交换机上设置登录口令:
switch(enable) set password
switch(enable) set enalbepass
3.在基于IOS的交换机上设置远程访问:
switch(config)# interface vlan 1
switch(config-if)# ip address ip-address netmask
switch(config-if)# ip default-gateway ip-address
在基于CLI的交换机上设置远程访问:
switch(enable) set interface sc0 ip-address netmask broadcast-address
switch(enable) set interface sc0 vlan
switch(enable) set ip route default gateway
4.在基于IOS的交换机上启用和浏览CDP信息:
switch(config-if)# cdp enable
switch(config-if)# no cdp enable
为了查看Cisco邻接设备的CDP通告信息:
switch# show cdp interface [type modle/port]
switch# show cdp neighbors [type module/port] [detail]
在基于CLI的交换机上启用和浏览CDP信息:
switch(enable) set cdp module/port
为了查看Cisco邻接设备的CDP通告信息:
switch(enable) show cdp neighbors[module/port] [vlanduplexcapabilitiesdetail]
5.基于IOS的交换机的端口描述:
switch(config-if)# description description-string
基于CLI的交换机的端口描述:
switch(enable)set port name module/number description-string
6.在基于IOS的交换机上设置端口速度:
switch(config-if)# speed
在基于CLI的交换机上设置端口速度:
switch(enable) set port speed moudle/number
switch(enable) set port speed moudle/number
7.在基于IOS的交换机上设置以太网的链路模式:
switch(config-if)# duplex
在基于CLI的交换机上设置以太网的链路模式:
switch(enable) set port duplex module/number
8.在基于IOS的交换机上配置静态VLAN:
switch# vlan database
switch(vlan)# vlan vlan-num name vla
switch(vlan)# exit
switch# configure teriminal
switch(config)# interface interface module/number
switch(config-if)# switchport mode access
switch(config-if)# switchport access vlan vlan-num
switch(config-if)# end
在基于CLI的交换机上配置静态VLAN:
switch(enable) set vlan vlan-num [name name]
switch(enable) set vlan vlan-num mod-num/port-list
9. 在基于IOS的交换机上配置VLAN中继线:
switch(config)# interface interface mod/port
switch(config-if)# switchport mode trunk
switch(config-if)# switchport trunk encapsulation
switch(config-if)# switchport trunk allowed vlan remove vlan-list
switch(config-if)# switchport trunk allowed vlan add vlan-list
在基于CLI的交换机上配置VLAN中继线:
switch(enable) set trunk module/port [onoffdesirableautononegotiate]
Vlan-range [isldotlqdotl0lanenegotiate]
10.在基于IOS的交换机上配置VTP管理域:
switch# vlan database
switch(vlan)# vtp domain domain-name
在基于CLI的交换机上配置VTP管理域:
switch(enable) set vtp [domain domain-name]
11.在基于IOS的交换机上配置VTP 模式:
switch# vlan database
switch(vlan)# vtp domain domain-name
switch(vlan)# vtp
switch(vlan)# vtp password password
在基于CLI的交换机上配置VTP 模式:
switch(enable) set vtp [domain domain-name] [mode{ severcilenttransparent }][password password]
12. 在基于IOS的交换机上配置VTP版本:
switch# vlan database
switch(vlan)# vtp v2-mode
在基于CLI的交换机上配置VTP版本:
switch(enable) set vtp v2 enable
13. 在基于IOS的交换机上启动VTP剪裁:
switch# vlan database
switch(vlan)# vtp pruning
在基于CL I 的交换机上启动VTP剪裁:
switch(enable) set vtp pruning enable
14.在基于IOS的交换机上配置以太信道:
switch(config-if)# port group group-number [distribution ]
在基于CLI的交换机上配置以太信道:
switch(enable) set port channel moudle/port-range mode
15.在基于IOS的交换机上调整根路径成本:
switch(config-if)# spanning-tree [vlan vlan-list] cost cost
在基于CLI的交换机上调整根路径成本:
switch(enable) set spantree portcost moudle/port cost
switch(enable) set spantree portvlancost moudle/port [cost cost][vlan-list]
16.在基于IOS的交换机上调整端口ID:
switch(config-if)# spanning-tree[vlan vlan-list]port-priority port-priority
在基于CLI的交换机上调整端口ID:
switch(enable) set spantree portpri priority
switch(enable) set spantree portvlanpri priority [vlans]
17. 在基于IOS的交换机上修改STP时钟:
switch(config)# spanning-tree [vlan vlan-list] hello-time seconds
switch(config)# spanning-tree [vlan vlan-list] forward-time seconds
switch(config)# spanning-tree [vlan vlan-list] max-age seconds
在基于CLI的交换机上修改STP时钟:
switch(enable) set spantree hello interval[vlan]
switch(enable) set spantree fwddelay delay [vlan]
switch(enable) set spantree maxage agingtiame[vlan]
18. 在基于IOS的交换机端口上启用或禁用Port Fast 特征:
switch(config-if)#spanning-tree portfast
在基于CLI的交换机端口上启用或禁用Port Fast 特征:
switch(enable) set spantree portfast
19. 在基于IOS的交换机端口上启用或禁用UplinkFast 特征:
switch(config)# spanning-tree uplinkfast [max-update-rate pkts-per-second]
在基于CLI的交换机端口上启用或禁用UplinkFast 特征:
switch(enable) set spantree uplinkfast [rate update-rate] [all-protocols offon]
20. 为了将交换机配置成一个集群的命令交换机,首先要给管理接口分配一个IP地址,然后使用下列命令: switch(config)# cluster enable cluster-name
21. 为了从一条中继链路上删除VLAN,可使用下列命令:
switch(enable) clear trunk module/port vlan-range
22. 用show vtp domain 显示管理域的VTP参数.
23. 用show vtp statistics显示管理域的VTP参数.
24. 在Catalyst交换机上定义TrBRF的命令如下:
switch(enable) set vlan vlan-name [name name] type trbrf bridge bridge-num[stp ]
25. 在Catalyst交换机上定义TrCRF的命令如下:
switch (enable) set vlan vlan-num [name name] type trcrf
{ring hex-ring-numdecring decimal-ring-num} parent vlan-num
26. 在创建好TrBRF VLAN之后,就可以给它分配交换机端口.对于以太网交换,可以采用如下命令给VLAN分配端口:
switch(enable) set vlan vlan-num mod-num/port-num
27. 命令show spantree显示一个交换机端口的STP状态.
1、在【开始】菜单栏中选择【控制面板】。2、点击【声音】。3、点击【录制】栏。4、双击【麦克风】。5、选择【级别】选项。6、调节麦克风声音大小。7、检查是否被静音。8、如被静音则点击【喇叭】将图标开启。
(0)人喜欢2024-09-201、首先,打开自己的电脑,点击桌面上的“计算机”按钮。2、在“计算机”中选择:打开控制面板。然后在选择“个性化”设置。3、在个性化中就可以选择电脑中已经存在的一些桌面壁纸,选择出自己喜欢的一款,选择确认就可以了。4、如果
(0)人喜欢2024-09-201、在“我的电脑”上右键点击,选择“属性”。2、在出现的系统界面中,点击“高级系统设置”。3、选择“高级”选择,在启动和故障恢复中,点击“设置”。4、在系统失败中,将“自动重新启动”的√取消掉,确定即可。5、“win+r
(0)人喜欢2024-09-20IOS14.2微信闪退怎么解决?对于IOS14的所有测试版本都是不稳定和有BUG的,所以用户们出现微信闪退也在意料之中,这不是一个大问题,只是系统适配没有适配好
(2)人喜欢2024-09-201、在【开始】菜单栏中选择【控制面板】。2、点击【声音】。3、点击【录制】栏。4、双击【麦克风】。5、选择【级别】选项。6、调节麦克风声音大小。7、检查是否被静音。8、如被静音则点击【喇叭】将图标开启。
(0)人喜欢2024-09-201、首先,打开自己的电脑,点击桌面上的“计算机”按钮。2、在“计算机”中选择:打开控制面板。然后在选择“个性化”设置。3、在个性化中就可以选择电脑中已经存在的一些桌面壁纸,选择出自己喜欢的一款,选择确认就可以了。4、如果
(0)人喜欢2024-09-201、在“我的电脑”上右键点击,选择“属性”。2、在出现的系统界面中,点击“高级系统设置”。3、选择“高级”选择,在启动和故障恢复中,点击“设置”。4、在系统失败中,将“自动重新启动”的√取消掉,确定即可。5、“win+r
(0)人喜欢2024-09-20IOS14.2微信闪退怎么解决?对于IOS14的所有测试版本都是不稳定和有BUG的,所以用户们出现微信闪退也在意料之中,这不是一个大问题,只是系统适配没有适配好
(2)人喜欢2024-09-20